|
|
|
|
|
|
Joist Brdg 2x8-10in Tension - Case of 200
|
|
|
Spans 2 joists per unit, typically used for bridging or bracing I-joists. Must be installed before subfloor sheathing to reduce joist movement and subsequent floor noise. G90 galvanizing finish. Requires 8d x 1-1/2 nails. Meets ICC-ES ESR-1781, FL13285 and L.A. City RR25843 codes. For additional information including I-joist installation, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. 22 Gauge.
|
|
|
|
|
|
|
|
|
|
Truss Spacer 1-1/2x120in Multi - Case of 20
|
|
|
Fast and accurate spacing guides for trusses, rafters or floor joists. Lightweight and compact, eliminates need to mark layouts on bearing plates, improves installation speed and helps to eliminate spacing errors. Do not rely on TSX for bracing. Requires one 8d nail per end. 10'L overall; 24" O.C. spacing. 22 Gauge - 5 Sections/Piece.
|
|
|
|
|
|
|
|
|
|
Joist Brdg 2x10-12in Grp Tooth - Case of 100
|
|
|
Special teeth grip joists for easy single-nail installation. Can be installed before or after subfloor is in place (sheathing) to reduce joist movement and subsequent floor noise. G90 galvanizing finish. Requires one 8d x 1-1/2 nail. Meets ICC-ES ESR-1781, FL13285 and L.A. City RR25843 codes. For additional information on standard lumber installation, Please See USP Lumber Connectors charts in the Orgill paper catalog D10 Reference Pages. 22 Gauge - 2 x 10 Joist Size.
|
|
|
|
|
|
|
|
|
|
Truss Spacer 1-1/2x25-1/2in sg - Case of 50
|
|
|
Fast and accurate spacing guides for trusses, rafters or floor joists. Lightweight and compact, eliminates need to mark layouts on bearing plates, improves installation speed and helps to eliminate spacing errors. Do not rely on the TS for bracing. Requires (1) 8d nail per end to fasten units to trusses, rafters or floor joists. 2'L overall; 24" O.C. spacing. 20 Gauge - 1 Section/Piece.
|
|
|
|
|
|
|
|
|
|
Joist Brdg 1x44in OveR-Under - Case of 50
|
|
|
Spans three joists in under/over installation; prong teeth in the center helps reduce nailing. G90 galvanizing finish; bridging should be installed on floor joists with a nominal depth-to-thickness ratio of 5 to 6 or more (2055 National Design Specification for Wood Construction; Section 4.4.1). Install prior to subfloor sheathing; use (2) 8d x 1-1/2" nails at each end. Fully seat nails to avoid any movement against the bridging and subsequent floor noise. 18 Gauge.
|
|
|
|
|
|
|
|
|
|
Joist Brdg 2x8-10in SnaP-On gv - Case of 100
|
|
|
No-nail bridging. Place in existing floor system where joist movement is suspected to reduce movement and subsequent floor noise. 2 piece construction creates a solid diagonal brace against joist movement. G90 galvanizing finish. Shipped as 1 piece that easily breaks into 2 pieces at center for proper installation. Meets ICC-ES ESR-1781, FL3285 and L.A. City RR25843 codes. For additional information on standard lumber installation, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. 22 Gauge - 2 x 8-10-12 Joist Size.
|
|
|
|
