|
|
|
|
|
|
Irwin 324011 Standard Tip Hammer Drill Bit, 5/8 in Dia x 11 in OAL, Chrome Vanadium Steel
|
|
|
Flute geometry removes dust from the hole quicker for fast drilling and long life. Shot peened, double-tempered finish reduces breakage. Copper braze material gives high heat resistance for reduced tip loss. Chrome vanadium shaft through-hardened to 50-53HrC. Fits all spline rotary hammers.
|
|
|
|
|
|
|
|
|
|
Irwin 324005 Standard Tip Hammer Drill Bit, 1/2 in Dia x 16 in OAL, Chrome Vanadium Steel
|
|
|
Flute geometry removes dust from the hole quicker for fast drilling and long life. Shot peened, double-tempered finish reduces breakage. Copper braze material gives high heat resistance for reduced tip loss. Chrome vanadium shaft through-hardened to 50-53HrC. Fits all spline rotary hammers.
|
|
|
|
|
|
|
|
|
|
BIT HMR SPLN SHNK 1/2X11X16IN
|
|
|
|
|
|
|
|
|
|
|
|
|
Speedx HC4501 Rotary Hammer Drill Bit, 3/8 in Dia, 13 in L, (2) 8 in Spiral Flute, Spline Shank Centric Point, Carbide
|
|
|
The carbide tipped bit head is harder and more resistant to extreme loads. Fits Bosch as well as other spline hammers.
|
|
|
|
|
|
|
|
|
|
Irwin 324012 Standard Tip Hammer Drill Bit, 5/8 in Dia x 16 in OAL, Chrome Vanadium Steel
|
|
|
Flute geometry removes dust from the hole quicker for fast drilling and long life. Shot peened, double-tempered finish reduces breakage. Copper braze material gives high heat resistance for reduced tip loss. Chrome vanadium shaft through-hardened to 50-53HrC. Fits all spline rotary hammers.
|
|
|
|
|
|
|
|
|
|
BIT HMR SPLN SHNK 5/8X11X16IN
|
|
|
|
|
|
|
|
|
|
|
|
|
Irwin 324001 Standard Tip Hammer Drill Bit, 3/8 in Dia x 13 in OAL, Chrome Vanadium Steel
|
|
|
Flute geometry removes dust from the hole quicker for fast drilling and long life. Shot peened, double-tempered finish reduces breakage. Copper braze material gives high heat resistance for reduced tip loss. Chrome vanadium shaft through-hardened to 50-53HrC. Fits all spline rotary hammers.
|
|
|
|
|
|
|
|
|
|
Speedx HC4511 Rotary Hammer Drill Bit, 1/2 in Dia, 13 in L, (2) 8 in Spiral Flute, Spline Shank Centric Point, Carbide
|
|
|
The carbide tipped bit head is harder and more resistant to extreme loads. Fits Bosch as well as other spline hammers.
|
|
|
|
|
|
|
|
|
|
Irwin 324004 Standard Tip Hammer Drill Bit, 1/2 in Dia x 13 in OAL, Chrome Vanadium Steel
|
|
|
Flute geometry removes dust from the hole quicker for fast drilling and long life. Shot peened, double-tempered finish reduces breakage. Copper braze material gives high heat resistance for reduced tip loss. Chrome vanadium shaft through-hardened to 50-53HrC. Fits all spline rotary hammers.
|
|
|
|
|
|
|
|
|
|
BIT HMR SPLN SHNK 3/4X11X16IN
|
|
|
|
|
|
|
